Adjust the Image Sensor PIR sensitivity on a Qolsys IQ Panel 2
By default, the Image Sensor is configured with a standard motion sensitivity profile Normal . The sensor can also be set to a more sensitive motion profile (i.e., High ) and a less sensitive profile with pet immunity for pets up to 40 lbs (i.e., Low ). Adjust the PIR sensitivity Use the Partner Portal or Mobile…
What is the difference between the Qolsys IQ Panel 2 and the IQ Panel 2 Plus?
Unlike the Qolsys IQ Panel 2, the IQ Panel 2 Plus includes a built-in PowerG daughtercard. Since the PowerG daughtercard uses the same antenna as the Image Sensor daughtercard, the IQ Panel 2 Plus is not compatible with the Image Sensor. The Qolsys IQ Panel 2 and 2 Plus are both compatible with the PowerG PIR camera…
Connect a Qolsys IQ Panel 2 to a Wi-Fi network
The Qolsys IQ Panel 2 is compatible with Dual-Path Wi-Fi communication. The panel can be connected to a Wi-Fi network using the panel, Partner Portal, or MobileTech app. Note : A communication test must be performed to initially register the cellular module before a Wi-Fi or Dual-Path test is performed. If a communi…
Find The Signal Strength of a Qolsys IQ Panel 2
Panel signal strength can be requested locally at the panel. To find the signal strength using the Qolsys IQ Panel 2: * Go to the home screen. * Tap Settings . * Tap Advanced Settings . * Enter the installer code. * Tap About . * Tap Cellular to view the Cellular Signal Strength .
What is PowerG on the Qolsys IQ Panel 2?
PowerG is a commercial-grade, two-way communications protocol with an extreme range of over 6,000 feet (about 2,000 meters), much greater than the industry standard. The signal automatically adjusts to preserve device battery life, up to eight years. The PowerG network uses Frequency Hopping Spread Spectrum technolo…
Run Scenes from the Qolsys IQ Panel 2
The Qolsys IQ Panel 2 has the ability to run Alarm.com Scenes locally at the panel. For more information about configuring Scenes, see Create/edit a Scene . Compatibility To following are required to locally run Scenes. * The Qolsys IQ Panel 2 must be on firmware version 2.4.0+. * Local Scenes support must be e…
Configure Bluetooth disarming on the Qolsys IQ Panel 2
Bluetooth Low Energy (BLE) 4.0 is built into the IQ Panel 2. The Qolsys IQ Panel 2 allows for up to five mobile Bluetooth devices to be paired with the panel. Pairing mobile Bluetooth devices allow for Bluetooth disarm, which disarms the system from an armed away state when the connected mobile device comes within ra…
Enable Doorbell Camera Notifications to Qolsys IQ Panel 2
Receive notifications on the Qolsys IQ Panel 2 screen when a doorbell camera detects motion or the button is pushed. Requirements To enable doorbell camera notifications to the Qolsys IQ Panel 2: Service package A service package that supports at least one doorbell camera. Panel hardware Firmware versio…
Interact with a Z-Wave device from a Qolsys IQ Panel 2
The Qolsys IQ Panel 2 allows users to interact with Z-Wave lights, locks, thermostats, and garage devices locally at the panel. For information about adding Z-Wave devices, see Manage Z-Wave devices on a Qolsys IQ Panel 2 . Note : Additional Z-Wave devices may be able to be added and controlled locally. For more in…
Bypass a sensor on a Qolsys IQ Panel 2
On the Qolsys IQ Panel 2, it is possible to bypass an open contact sensor, or any sensor with a trouble condition (e.g., tamper, low battery, offline, etc.) when arming a system from the Customer Website or app. Simply sending an arming command will automatically bypass all zones that would prevent arming. A motion s…
