Customize the Panel Setup Wizard for the Qolsys IQ Panel 2
Qolsys IQ Panel 2 — Customize the Panel Setup Wizard Several steps of the panel setup wizard on the Qolsys IQ Panel 2 can be customized remotely using the Partner Portal or the MobileTech app. This lets you streamline installation, hide unneeded steps, or enforce best-practice defaults. Requirements * Qolsys IQ…
Qolsys IQ Panel 2 Software Version 2.5.1 - User Guide
Third-Party Guide Disclaimer The guides attached to this page have been written by a third party and are not maintained by True Protection . Important: Any questions regarding the installation, maintenance, or usage instructions in these guides should be directed to the device manufacturer . Get Help from Tru…
Run Scenes from the Qolsys IQ Panel 2
Program Sensors Remotely on Qolsys IQ Panel 2 Note: Device partitions can be configured on the Qolsys IQ Panel 2 with firmware version 2.3.0+. Program Sensors Using the Partner Portal * Log into the Partner Portal and locate the customer account. * Click Equipment → Sensors . * Configure an existing device:…
Enable the Qolsys IQ Panel 2 Glass Break Detector
Qolsys IQ Panel 2: Enable the Built-In Glass Break Detector The Qolsys IQ Panel 2 includes a built-in glass break detector that’s fully supported by Alarm.com. No extra service add-on is required. Once enabled, it appears in the equipment list under the next available sensor ID as Panel Glass Break . Enable from…
Enable the Manage My System Landing Page on a Qolsys IQ Panel 2
Qolsys IQ Panel 2 – “Manage My System” Landing Page What You’ll See * Wi-Fi connectivity status (connected/disconnected, useful before dual-path testing) * Panel software version (verify before scheduling firmware updates) * Bluetooth radio state (On/Off; helpful when using Bluetooth Disarming) Note: There a…
Qolsys IQ Panel 2 - Panel-specific app feature compatibility
Alarm.com App Features with Qolsys IQ Panel 2 Some Alarm.com mobile app features may be available or unavailable due to panel limitations and app version. Use this page to understand how key arming features behave when your system uses a Qolsys IQ Panel 2 . App Feature Matrix (IQ Panel 2) Panel Silent Arming …
Improve Image Sensor signal strength with a Qolsys IQ Panel 2
Alarm.com Image Sensor RF Signal Strength & Troubleshooting About RF Signal Strength The Alarm.com Image Sensor communicates via RF with its daughterboard. For reliable operation: * Minimum: 30% signal strength * Recommended: 40%+ signal strength Applies to: Image Sensor version 2 & 2.2 models (ADC-IS-200, AD…
Enroll an Image Sensor on a Qolsys IQ Panel 2
Qolsys IQ Panel 2 – Enroll Image Sensors Requirements * Image Sensor daughter card is installed on the IQ Panel 2. * Customer account includes the Images add-on. * A communication test has completed successfully ( how to send ). Helpful: Ensure the panel is connected to Wi-Fi for smoother provisioning ( Wi…
Qolsys IQ Panel 2 - Sensor Groups
Qolsys IQ Panel 2 — Sensor Groups Sensor groups define how each sensor behaves when connected to the Qolsys IQ Panel 2. They determine how the system responds to triggers such as doors opening, motion detection, or glass breakage. What Are Sensor Groups? Each sensor enrolled on the IQ Panel 2 must be assigned to a…
Interact with Garage Doors from a Qolsys IQ Panel 2
Qolsys IQ Panel 2 – Control Z-Wave & LiftMaster Garage Doors Overview The Qolsys IQ Panel 2 lets you view status and open/close compatible Z-Wave Linear and LiftMaster garage door devices directly from the panel. Firmware requirement: For LiftMaster compatibility, the panel must be on firmware 2.4.0+ . Aft…
