Qolsys IQ Panel 2 - Battery Replacement
The Qolsys IQ Panel 2 requires a special battery pack available for purchase from the manufacturer. To replace the battery in a Qolsys IQ Panel 2: If desired, put the system in test mode with the monitoring station before proceeding. For more information, see Put a system On Test with the monitoring station . Cau…
What is the difference between the Qolsys IQ Panel 2 and the IQ Panel 2 Plus?
Unlike the Qolsys IQ Panel 2, the IQ Panel 2 Plus includes a built-in PowerG daughtercard. Since the PowerG daughtercard uses the same antenna as the Image Sensor daughtercard, the IQ Panel 2 Plus is not compatible with the Image Sensor. The Qolsys IQ Panel 2 and 2 Plus are both compatible with the PowerG PIR camera…
How do multiple partitions work with the Qolsys IQ Panel 2?
Compatibility * On panel firmware version below 2.3.0, the Qolsys IQ Panel 2 supports one partition. * On panel firmware version 2.3.0+, the Qolsys IQ Panel 2 supports up to four partitions. For more information about updating the panel firmware remotely, see Upgrade the firmware on a Qolsys IQ Panel 2 . Remotel…
Enable the Manage My System Landing Page on a Qolsys IQ Panel 2
The Qolsys IQ Panel 2 supports the Manage My System landing page enabling users to see the panel’s Wi-Fi connectivity status, the panel's software version, and the state of the panel’s Bluetooth radio. The following image is an example of how the Manage My System landing page appears on the Qolsys IQ Panel 2 s…
Configure Bluetooth disarming on the Qolsys IQ Panel 2
Bluetooth Low Energy (BLE) 4.0 is built into the IQ Panel 2. The Qolsys IQ Panel 2 allows for up to five mobile Bluetooth devices to be paired with the panel. Pairing mobile Bluetooth devices allow for Bluetooth disarm, which disarms the system from an armed away state when the connected mobile device comes within ra…
Interact with a Z-Wave device from a Qolsys IQ Panel 2
The Qolsys IQ Panel 2 allows users to interact with Z-Wave lights, locks, thermostats, and garage devices locally at the panel. For information about adding Z-Wave devices, see Manage Z-Wave devices on a Qolsys IQ Panel 2 . Note : Additional Z-Wave devices may be able to be added and controlled locally. For more in…
Connect a Qolsys IQ Panel 2 to a Wi-Fi network
The Qolsys IQ Panel 2 is compatible with Dual-Path Wi-Fi communication. The panel can be connected to a Wi-Fi network using the panel, Partner Portal, or MobileTech app. Note : A communication test must be performed to initially register the cellular module before a Wi-Fi or Dual-Path test is performed. If a communi…
Run Scenes from the Qolsys IQ Panel 2
The Qolsys IQ Panel 2 has the ability to run Alarm.com Scenes locally at the panel. For more information about configuring Scenes, see Create/edit a Scene . Compatibility To following are required to locally run Scenes. * The Qolsys IQ Panel 2 must be on firmware version 2.4.0+. * Local Scenes support must be e…
Enroll an Image Sensor on a Qolsys IQ Panel 2
Requirements The following are required to enroll Image Sensors to a Qolsys IQ Panel 2: * The Qolsys Image Sensor daughter card must be installed. For more information about installing the Image Sensor daughter card on the Qolsys IQ Panel 2, see Qolsys IQ Panel 2 Image Sensor IQ Card Installation . * The custome…
Send a Communication Test from IQ Panel 2
Sending a communication test from the panel initiates communication and verifies that the module is communicating on the cellular network. For this test to send a signal to the monitoring station, verify Manual/Auto Tests are selected as an Event to Forward in the customer's Monitoring Settings . For more info…
