• ADC-V723 camera (included).
• AC power adapter (included).
• Wireless (2.4 or 5 GHz) connection to broadband (Cable, DSL, or Fiber Optic) internet. For more information about bandwidth requirements, see What are the internet service and bandwidth requirements for Alarm.com video devices?.
• A computer, tablet, or smartphone with Wi-Fi is required if the router does not have the Wi-Fi Protected Setup (WPS) feature.

There are two options for connecting the V723 to the Wi-Fi network: Access Point (AP) mode or Wi-Fi Protected Setup (WPS) mode. Use WPS mode if you have easy access to the customer’s router and the router has the WPS feature enabled.

Note: Some Internet Service Providers disable the WPS feature on customer routers. AP mode is the most reliable method for installing this device.

In the box

• V723 camera
• Mounting plate
• Power supply (10 feet)
• Installation guide
• Wall anchors & screws (x2)

For a detailed list of this video device's features, see 1080p Outdoor Wi-Fi Camera (ADC-V723) - Data Sheet.

Overview

Articulation

Installation

Physical installation recommendations

• In a shaded area or under cover (e.g., under an eave)
• Mounting bracket installed on a vertical surface
• Camera face oriented with a downward tilt
• SD card door facing downwards

For more information about general video installation and maintenance guidelines, see Video Installation Best Practices.

Customer - mobile app installation wizard

Note: If you are a customer, please download the mobile app in the app store. If you already use the mobile app, please make sure that you are using the latest version.

1. Log in to the mobile app.
2. Tap the navigation menu .
3. Tap  + Add Device.
4. Tap Video Camera.
5. Tap ADC-V723 (If you do not see the Add Device option, please use the AP mode or WPS mode instructions below to complete your installation).
6. Follow the on-screen instructions to finish adding the camera.

Service provider technician - MobileTech installation

1. Log in to MobileTech.
2. Select the customer’s account.
3. Tap Quick Actions.
4. Tap Add Device.
5. Tap Video.
6. Follow the on-screen instructions to finish adding the camera.

AP mode

Important: To ensure sufficient Wi-Fi signal, complete these steps with the camera near its final location but prior to mounting.

1. Connect the camera’s AC power adapter and plug it into a non-switched outlet. If the standard power supply is too short to reach an outlet, extension cables are available for the video device. For more information about how to extend the power supply, see How do I extend the power supply of a camera?.
2. The camera’s LED will begin to flash white. If the LED is not white after two minutes, hold down the Reset button  and release when the LED begins to flash white (about 6 seconds).
3. On a Wi-Fi enabled device, connect to the wireless network ADC-V723 (XX:XX:XX) where XX:XX:XX is the last six digits of the ADC-V723’s MAC address, which is located on the bottom of the camera or on the packaging.
4. On the same device, open a web browser and enter http://v723install or 192.168.1.1 in the URL field. Follow the on-screen instructions to add the ADC-V723 to the Wi-Fi network:
   1. Click Scan.
      
      
       
   2. Click to select the customer's network. The SSID field will automatically populate with the selected network name.
      
      
       
   3. In Password, enter the Wi-Fi password.
      
      
       
   4. Click Submit. The LED will be solid green when the connection is complete.
5. Add the device to the account by selecting the account in the MobileTech app, by using the Customer app Video Installation Wizard, or by using a web browser and entering the following web address: www.alarm.com/addcamera (you will need the customer’s user name and password if using the Customer Website or app). For more information about adding a camera to an account, see Enroll the video device to the customer account. 
6. Select the camera from the video device list or type in its MAC address to begin adding the camera. The camera’s MAC address is located on the bottom of the camera or on the packaging.
7. Follow the on-screen instructions to finish adding the camera. You may configure camera settings using the Customer Website.

You can now power down the camera and install it in its final location using the included hardware.

WPS mode

Important: To ensure sufficient Wi-Fi signal, complete these steps with the camera near its final location but prior to mounting.

1. Connect the camera’s AC power adapter and plug it into a non-switched outlet.  If the standard power supply is too short to reach an outlet, extension cables are available for the video device. For more information about how to extend the power supply, see How do I extend the power supply of a camera?.
2. Hold down the Reset button  on the bottom of the camera and release when the LED begins to flash blue (about 3 seconds).
3. Activate the WPS Mode on the router. The router will begin to connect to the wireless network. The LED will be solid green when the connection is complete.
4. Add the device to the account by selecting the account in the MobileTech app, by using the Customer app Video Installation Wizard, or by using a web browser and entering the following web address: www.alarm.com/addcamera (you will need the customer’s user name and password if using the Customer Website or app). For more information about adding a camera to an account, see Enroll the video device to the customer account. 
5. Select the camera from the video device list or type in its MAC address to begin adding the camera. The camera’s MAC address is located on the bottom of the camera or on the packaging.
6. Follow the on-screen instructions to finish adding the camera.

You may configure camera settings from the Customer Website. You can now power down the camera.

LED reference guide

LED pattern	Description
	Power off
	Connected to Alarm.com
	Local network connection
	Camera reverting to factory default settings
	No local or Internet connection
	Power on, camera booting
	WPS mode
	Wi-Fi access point mode

Troubleshooting

• If you have issues connecting the camera to the account, power cycle the camera and try again.
• If issues persist, reset the camera to factory defaults. Press and hold the Reset button  located on the bottom of the camera until the LED is flashing Green and Red (about 15 seconds), then release the button. The camera will reboot with factory defaults. For more information about the reset procedure, see Factory reset an ADC-V723 to its default settings.
  Important: If the camera was previously installed to an Alarm.com account, it will need to be deleted before it can be installed again.
   
• Prolonged exposure to sunlight in extreme conditions may impact the camera’s performance. The optimal installation location is in a shaded area (e.g., under an eave).