The 2GIG-DBELL1-345 is a wireless RF doorbell that enrolls to the 2GIG GoControl like a sensor, and can be used for triggering notifications and video recordings for existing video cameras. There is no additional Service Package add-on required for the customer to enroll the 2GIG doorbell.

This wireless doorbell sounds one of 11 selectable chimes when the pushbutton is pressed. The DBELL1 wireless doorbell has a range of up to 350 feet and can be powered using battery or low voltage wiring.

Note: The 2GIG Smart Video Doorbell Camera is not compatible with Alarm.com.

For the full 2GIG-DBELL-345 installation guide, see 2GIG's Doorbell Installation Instructions. 

To program the 2GIG doorbell using the 2GIG GoControl: 

Note: To scroll between options, tap the ← or → arrows. To move to the previous or next prompts, tap the ↑ or ↓ arrows.

1. Tap Security.
2. Tap Menu. 
3. Tap Toolbox. 
4. Enter the installer code. 
5. Tap → to Toolbox (3 of 3). 
6. Tap Installer Toolbox. 
7. Tap System Configuration. 
8. Select RF sensor # (01 to 48) to assign the doorbell to an empty sensor number.
9. Select RF sensor type. The recommended group is (23) no response type, this allows the system to chime when the doorbell is pressed but not trigger an alarm.
10. Select RF equipment type. The recommended type is (1) contact.
11. Select RF sensor equipment code. Enter 1063 for the DBELL1‐345 2GIG doorbell.
12. Enter RF sensor serial number (7 digits).
    • For manual entry: Enter in the last seven digits of the TX ID that is found outside of the box or on the back of the device.
    • For auto entry:
      1. Tap Shift. 
      2. Tap Learn to put the panel into Learn‐in mode.
      3. Press the button on the doorbell to trigger the device.
      4. The correct TX ID appears on the 2GIG GoControl screen. Tap Ok to accept the correct TX ID.
         Note: Remember to tap the ↓ arrow to continue going through the 2GIG system configuration prompts.
13. Select RF sensor equipment age (0 to 1).
    • If the doorbell is new, enter (0) new. 
    • If the doorbell is an existing device, enter (1) existing. 
14. Select RF sensor 1 loop number (1 to 3). The loop number for a contact is (1) 1. 
15. Select RF sensor 1 dialer delay. Enter (0) disabled. 
16. Construct RF sensor voice descriptor. Tap Insert, and then enter any number between 002 and 255 to add a word.
    • For example, to name the doorbell front door, tap Insert and then press 098 for FRONT. Press Insert again, and then press 058 for DOOR. Tap ↓ to continue configuring the system. For a full list of voice descriptors, see page 2 of the 2GIG GoControl Installation Guide - Quick Programming Guide. 
17. Select RF sensor reports (0 to 1).
    • To disable reports, enter (0) disabled.
    • To enable reports, enter (1) enabled.
18. Select RF sensor supervised (0 to 1).
    • To disable reports for loss of supervision, enter (0) disabled.
    • To enable reports for loss of supervision, enter (1) enabled. 
19. Select RF sensor chime (0 to 13).
    • To disable the panel chime when the sensor is activated, enter (0) disabled. 
    • To select a voice and chime to sound when the sensor is activated, enter a number from 1 through 13 to enable the chime. 
20. To program another sensor, tap Next.
21. To exit programming, tap Skip and then tap End and exit. Upon exit, the panel reboots. Allow a few minutes for the panel to turn back on, and then test the sensor. 

Test the 2GIG doorbell

Before mounting the sensor, verify that the sensor mounting location provides good RF communication to the panel.

To verify good RF communication to the 2GIG GoControl:

1. Tap Security.
2. Tap Menu. 
3. Tap Toolbox. 
4. Enter the installer code. 
5. Tap → to Toolbox (3 of 3). 
6. Tap Installer Toolbox. 
7. Tap Walk Test. 
8. Press and release the doorbell button, and listen for chime or keypad beeps to determine the appropriate response. For more information, refer to the 2GIG Control Panel Install Guide. 
9. Exit the Installer Toolbox.

Mount the 2GIG doorbell in the location that is verified to receive good RF communication. For information about mounting the doorbell, see 2GIG's Doorbell Mounting Install Instructions. 

Optionally after programming and mounting the 2GIG doorbell, verify the household 24V AC connection is working by pressing the doorbell button to ring the doorbell.

Alarm.com notifications and rules

Requirements

To activate notifications and rules for the 2GIG doorbell:

• The customer must have Sensor Activity Monitoring (SAM) enabled on their account. For more information about SAM, see Enable or disable Sensor Activity Monitoring. 
• The doorbell must be programmed in the panel as an RF sensor. The sensor group Alarm.com generally recommends is 23-No Response Type, which allows for notifications when the doorbell is activated. 

Notification setup

To set up a 2GIG doorbell button push to send a notification, create a Sensor Activity notification. For more information about setting up notifications, see Create/edit a notification. 

Video recording setup

Important: The customer must have a video camera associated to their Alarm.com account to set up video recordings triggered by the 2GIG doorbell. 

To set up a 2GIG doorbell button push to trigger a video recording, create a Sensor Opened or Closed recording rule.  For more information about setting up recording rules, see Create/edit a video recording rule. 

Secondary door chime 

The 2GIG doorbell can work with a secondary door chime, which is an external speaker source that outputs the door chime so the customer can hear it not only from the panel but from another location in the residence. Typically customers use a TS1 keypad to hear the panel from another location in the residence, but a secondary door chime is another option for customers to use. 

To program a compatible speaker or siren:

1. Wire the positive (+) wire to terminal 1, and the negative (-) wire to terminal 4.
2. In system programming, program Q78 to select option 11 then save the changes to panel programming. 
3. After Q78 is successfully programmed, test the device and door chime.  

Functions 

The 2GIG doorbell functions include: 

• Smooth, modern design
• White UV-resistant plastic
• Simple wireless installation (can be hard-wired)
• Surface mount
• 350 ft. range (open air)
• 11 selectable chimes
• Doorbell can illuminate Z-Wave lights when engaged
• Compatible with Scenes or Rules
• Receive text/email from Alarm.com when doorbell engaged
• Battery or low voltage for power
• Low battery indicator
• Battery included
• Weatherproof seal included

Specifications