152
Monitoring Station dialer codes are led with either a 1 or E to indicate the event signal and led with a 3 or R to indicate a restore signal. The event history on Alarm.com always displays the codes leading with a 1 to indicate the event and 3 to indicate the restore.
Reporting Zones
|
2GIG Type |
Description |
Type of Equipment |
CID / Restore Codes |
Comments |
|---|---|---|---|---|
|
1 |
Entry/exit 1 |
Contact |
1134 / 3134 (zone #) |
- |
|
2 |
Entry/exit 2 |
Contact |
1134 / 3134 (zone #) |
- |
|
3 |
Perimeter |
Contact / Glass Break |
1131 / 3131 (zone #) |
- |
|
4 |
Interior follower |
Motion / Contact |
1132 / 3132 (zone #) |
- |
|
5 |
Day zone |
Contact |
1135 / 3135 (zone #) 1156 / 3156 (zone #) |
Alarm Trouble |
|
6 |
24 hour Silent panic |
Button / Contact |
1122 / 3122 (zone #) |
- |
|
7 |
24 hour audible alarm |
Button / Contact |
1123 / 3123 (zone #) |
- |
|
8 |
24 hour Auxiliary alarm |
Contact |
1150 / 3150 (zone #) |
- |
|
8 |
24 hour Auxiliary alarm |
Emergency |
1100 / 3100 (zone #) |
Medical |
|
8 |
24 hour Auxiliary alarm |
Water |
1154 / 3154 (zone #) |
Water |
|
8 |
24 hour Auxiliary alarm |
Freeze |
1159 / 3159 (zone #) |
Freeze |
|
8 |
24 hour Auxiliary alarm |
High temperature |
1158 / 3158 (zone #) |
High temp |
|
9 |
24 hour fire |
Smoke /heat rise |
1110 / 3110 (zone #) |
- |
|
10 |
Interior with delay |
Motion / Contact |
1132 / 3132 (zone #) |
- |
|
14 |
24 hour CO |
CO detector |
1162 / 3162 (zone #) |
- |
|
16 |
Fire with verification |
Smoke detector |
1110 / 3110 (zone #) |
- |
|
23 |
No response |
Contact / motion |
NO REPORT |
- |
|
24 |
Silent Burglary |
Contact |
1146 / 3146 (zone #) |
- |
- Types 1, 2, 3, 4, 5 (alarm), 7, 10 follow Burglary Bell Cutoff Timer
- Types 9, 14,16 follow Fire Bell Cutoff Timer
- Types 8 has no bell cutoff and will not sound external sounder if used
- Types 5 (trouble) system disarmed will cause trouble beep 6 per minute until silenced or restored
- Restores; types 1, 2, 3, 4, 5, 6, 7, 9, 10, 14, 16, 24….. Restores depend on how swinger shutdown is set. For example:
- if swinger shutdown is set to two then the zone types above will send a restore if restores are enabled at bell cutoff or anytime after bell cutoff if the zone in question becomes good.
- If the same zone trips again no restore will be sent at bell cutoff even if the zone is good or becomes good; The reason for this is the zone can’t trip again during the same arming period because the swinger count of two has been reached.
- However when you disarm the system if the zone is good then a restore will be sent.
- If the zone is not good at disarm, a restore is never sent for the second trip.
- If swinger shutdown is set to one then restore will never be sent after the zone trips because the swinger shutdown count has been reached and therefore the zone can’t trip again.
- However if the zone is good at disarm a restore will be sent then for the trip while armed,
- if the zone is not good at disarm a restore is never sent for that zone.
Note: Types 9, 14, and 16 don’t participate in swinger shutdown so if the zone becomes good or is good at bell cutoff a restore is sent Type 8 since there is no bell cutoff for type 8 a restore is only sent when disarmed if the zone is good.
- if swinger shutdown is set to two then the zone types above will send a restore if restores are enabled at bell cutoff or anytime after bell cutoff if the zone in question becomes good.
Other Events
|
Event |
CID Code |
Comment |
|---|---|---|
|
Cellular Backup Failure |
1354 / 3354 |
- |
|
Zone Tamper |
1383 / 3383 (zone #) |
If the system is armed then the zone sends an alarm |
|
Zone Loss Of Supervision |
1381 / 3381 (zone #) |
- |
|
Zone Low Battery |
1384 / 3384 (zone #) |
- |
|
Zone Bypass |
1570 / 3570 (zone #) |
- |
|
Cross Zone Trouble |
1378 / 3378 (zone #) |
Zones 47 & 48 if enabled |
|
Panel Tamper |
1383 / 3383 zone 000 |
System state is disarmed. ADC doesn’t send restore |
|
Panel Tamper |
1137 / 3137 zone 000 |
The system state is armed. ADC doesn’t send restore |
|
Panel Low Battery |
1302 / 3302 zone 000 |
- |
|
Panel Loss Of AC |
1301 / 3301 zone 000 |
- |
|
Panel Programming entry |
1627 zone 000 |
Not sent by ADC |
|
Panel Programming exit |
1628 zone 000 |
Not sent by ADC |
|
Panel Walk Test Start |
1607 user # 001 |
ADC sends user 000 |
|
Panel Walk Test End |
3607 user # 001 |
ADC sends user 000 |
|
Panel Telephone Fail / Fail To Communicate Via Telephone |
1350 zone 000 |
ADC doesn’t send phone line restored |
|
Panel Siren Supervision |
1320 / 3320 zone 000 |
- |
|
Panel RF Jam |
1344 / 3344 zone 000 |
- |
|
Panel Loss Of Supervision Of Short Range Radio |
1381 / 3381 zone 000 |
This means RF receiver is not working or talking to panel. This happens armed or disarmed it takes approx 4:00 minutes to detect. ADC doesn’t send this event. |
|
Closing From Panel Touch Pad |
3401 user # |
User 000 sent for quick arming. |
|
Opening From panel touchpad |
1401 user # |
- |
|
Closing From KeyFob |
3401 user # (51-58) |
Keyfob’s 1-8 are considered users 51-58 |
|
Opening from keyfob |
1401 user # (51-58) |
Keyfob’s 1-8 are considered users 51-58 |
|
Console audible panic |
1123 / 3123 zone 099 |
ADC doesn’t send restore. Restore sent at bell cutoff or disarm |
|
Console Silent Panic |
1122 zone 099 |
No restore sent by ADC or dialer |
|
Console Fire |
1115 / 3115 zone 095 |
ADC doesn’t send restore. Restore sent at bell cutoff or disarm |
|
Console Medical (emergency) |
1100 / 3100 zone 096 |
ADC doesn’t send restore. Restore sent at bell cutoff or disarm. No external siren if installed |
|
RF keypad Police Audible |
1123 / 3123 zone 059 – 062 |
RF keypads are zones 59-62 ADC doesn’t send restore. Restore sent at bell cutoff or disarm |
|
RF Keypad Police Silent |
1122 zone 059 – 062 |
RF keypads are zones 59-62 |
|
RF keypad Fire |
(dialer sends) 1115 zone 059 – 062 (ADC sends) 1115 zone 095 |
RF keypads are zones 59-62 |
|
Duress Code |
1121 zone 092 |
- |
|
Cancel |
1406 (user#) |
User number of user who disarmed |
|
Exit Error |
1457(user#) / 3457(zone#) |
ADC sends user 0 dialer sends user # of who armed. The dialer also sends restore with zone number at bell cutoff or disarm. ADC and dial both send an alarm for the zone that causes the exit error |
|
Recent Closing |
1459 (user#) |
ADC sends user 0 dialer sends user # of who armed |
|
Lack Of Usage |
1654 / 3654 zone 000 |
- |
|
Manual telephone test |
1601 zone 000 |
- |
|
Manual Cell Phone test |
1601 zone 000 |
- |
|
Automatic Test |
1602 zone 000 |
- |
|
GSM Radio Loss Of Network |
1353 / 3353 000 |
Not sent by ADC |
|
Listen In to follow |
1606 000 |
This is sent on any alarm condition if two-way voice is enabled. There is no listen in sent for fire or CO and in fact if a listen-in session is in progress and there is a fire alarm or CO alarm the listen session is automatically ended. Also, if a fire or CO alarm is in progress, another alarm will not cause a listen in event to occur. The above is how the dialer works. ADC works similarly with the following exception; ADC sends listen in to follow even for fire but the panel never dials the call and tells the ADC back end that it should release the two-way- line. If a silent alarm or duress is sent the CS can only use listen in mode, VOX and talk mode are automatically disabled. |
